Wear resistance of glow-discharge nitrided 08Х18Н10 steel

Keywords

nitriding, stainless steels, wear resistance.

Cite as

Stechyshyn М. S., Skyba М. Ye., Stechyshyna N. М., Mashovets N. S., and Medvedchuk N. K. Wear resistance of glow-discharge nitrided 08Kh18N10 steel. Physicochemical Mechanics of Materials. 2023. 59(2), 123-129.

https://doi.org/10.15407/pcmm2023.02.123

Abstract

The influence of the modes of anhydrous nitriding of 08Kh18N10 steel on the phase com­po­sition, distribution of the main alloying elements, and the content of nitrogen in the nitride layer, microhardness distribution and specific wear of nitrided austenitic stainless steel was investigated. The conducted studies showed that with an increase in the tempe­rature and duration of nitriding of 08Kh18N10 steel, simultaneously with the increase in the thickness of the nitrided layer, the nitrogen content in it decreases and a drop in the hard­ness of the upper part of the nitride zone is observed. At the same time the hardness gra­dually increases to the maximum values typical of the boundary of the nitride and diffu­sion zones. Laboratory tests on hydroabrasive wear showed that, compared to the initial state, the wear resistance of 08Kh18N10 steel, nitrided at P = 120 Pa, T = 600°C for 3 h, increased twofold. Industrial tests of centrifuge rotors at processing plant confirmed the results of laboratory studies.

References

1. V. M. Fedirko, I. M. Pohrelyuk, O. H. Luk’yanenko, S. M. Lavrys’, M. V. Kindrachuk, O. I. Dukhota, O. V. Tisov, and V. V. Zahrebel’nyi, “Thermodiffusion saturation of the surface of VT22 titaniumalloy from a controlled oxygen-nitrogen-containing atmosphere in the stage of aging,” Mater. Sci., 53, No. 5, 691-701 (2018). https://doi.org/10.1007/s11003-018-0125-z
2. I. Pohrelyuk, O. Yaskiv, O. Tkachuk, and D. B Lee, “Formation of oxynitride layers on titanium alloys by gas diffusion treatment,” Metals and Mater. Int., 15, Is. 6, 949-953 (2009). https://doi.org/10.1007/s12540-009-0949-z
3. I. M. Pohrelyuk, V. M. Fedirko, and S. M. Lavrys, “Effect of preliminary ball burnishing on wear resistance of the nitrided VT22 alloy,” J. of Friction and Wear, 38, Is. 3, 221-224 (2017). https://doi.org/10.3103/S1068366617030114
4. I. M. Pohrelyuk, J. Padgurskas, O. V. Tkachuk, A. G. Luk’yanenko, V. S. Trush, and S. M. Lavrys, “Influence of oxynitriding on antifriction properties of Ti-6Al-4V titanium alloy,” J. of Friction and Wear, 41, Is. 4, 333-337 (2000). https://doi.org/10.3103/S1068366620040108
5. V. Hutsaylyuk, M. Student, Kh. Zadorozhna, O. Student, H. Veselivska, V. Gvosdetskii, P. Maruschak, and H. Pokhmurska, “Improvement of wear resistance of aluminum alloy by HVOF method,” J. of Mater. Research and Technol., 9, Is. 6, 16367-16377 (2020). https://doi.org/10.1016/j.jmrt.2020.11.102
6. M. M. Student, H. V. Pokhmurs’ka, V. V. Hvozdets’kyi, M. Y. Holovchuk, and M. S. Romaniv, “Effect of high-temperature corrosion on the gas-abrasive resistance of electric-arc coatings,” Mater. Sci., 45, No. 4, 481-489 (2009). https://doi.org/10.1007/s11003-010-9205-4
7. M. Student, V. Hvozdetskyi, T. Stupnytskyi, O. Student, P. Maruschak, O. Prentkovskis, and P. Skačkauskas, “Mechanical properties of arc coatings sprayed with cored wires with different charge compositions,” Coatings, 12, Is. 7, art. no. 925 (2022). https://doi.org/10.3390/coatings12070925
8. M. Student, V. Hvozdetskyi, O. Student, O. Prentkovskis, P. Maruschak, O. Olenyuk, and L. Titova, “The effect of increasing the air flow pressure on the properties of coatings during the arc spraying of cored wires,” J. of Mech. Eng., 69, Is. 4, 133-146 (2019).
9. M. Student, A. Vojtovych, H. Pokhmurska, O. Student, and P. Maruschak, “Mechanical characteristics and wear resistance of the cladding layers obtained by melting of cored wires with simultaneous vibration of substrate,” J. of Mech. Eng., 69, Is. 1, 109-122 (2019). https://doi.org/10.2478/scjme-2019-0009
10. V. Hutsaylyuk, M. Student, V. Dovhunyk, V. Posuvailo, O. Student, P. Maruschak, and I. Koval’chuck, “Effect of hydrogen on the wear resistance of steels upon contact with plasma electrolytic oxidation layers synthesized on aluminum alloys,” Metals, 9, Is. 3, art. no. 280 (2019). https://doi.org/10.3390/met9030280
11. M. Student, I. Pohrelyuk, J. Padgurskas, V. Hvozdets’kyi, Kh. Zadorozna, H. Chumalo, O. Student, and I. Kovalchuk, “The effect of heat treatment on the structural-phase state and abrasive wear resistance of a hard-anodized layer on aluminum alloy 1011,” Coatings, 13, Is. 2, art. no. 391 (2019). https://doi.org/10.3390/coatings13020391
12. H. Nykyforchyn, V. Kyryliv, O. Maksymiv, and O. Zvirko, “Mechanical fabrication methods of nanostructured surfaces,” in: Handbook of modern coating technologies. Fabrication methods and functional properties, Elsevier, Amsterdam (2021), pp. 25-67. https://doi.org/10.1016/B978-0-444-63240-1.00002-4
13. V. Kyryliv, Ya. Kyryliv, and N. Sas, “Formation of surface ultrafine Grain Structure and their physical and mechanical characteristics using vibration-centrifugal hardening,” Adv. in Mater. Sci. and Eng., art. no. 3152170 (2018). https://doi.org/10.1155/2018/3152170
14. H. Nykyforchyn, V. Kyryliv, O. Maksymiv, V. Kochubie, R. Boyko, and V. Dovhunyk, “Wear resistance of the surface nanocrystalline structure under an action of diethylene glycol medium,” Applied Nanoscience, 9, Is. 1, 1085-1090 (2019). https://doi.org/10.1007/s13204-018-0690-3
15. V. Kyryliv, V. Gurey, O. Maksymiv, I. Hurey, and Y. Kulyk, “Influence of the deformation mode on the force conditions of formation of the surface nanostructure of 40Kh steel,” Mater. Sci., 57, No. 3, 422-427 (2021). https://doi.org/10.1007/s11003-021-00556-9
16. M. Umemoto, K. Todaka, and K. Tsuchiya, “Formation of nanocrystalline structure in carbon steels by ball drop and particle impact techniques,” Mater. Sci. and Eng.: A, 375-377, Spec. Iss. 1-2, 899-904 (2004). https://doi.org/10.1016/j.msea.2003.10.198
17. T. O. Olugbade, and J. Lu, “Literature review on the mechanical properties of materials after surface mechanical attrition Treatment (SMAT),” Nano Mater. Sci., 2, 3-31 (2020). https://doi.org/10.1016/j.nanoms.2020.04.002
18. D. Lesyk, S. Maartinez, B. Mordyuk, V. Dzemelinskyi, A. Lamikiz, and G. Prokopenko, “Effects of laser heat treatment combined with ultrasonic impact treatment on the surface topography and hardness of carbon steel AISI 1045,” Opt. Laser Technol., 111, 424-438 (2019). https://doi.org/10.1016/j.optlastec.2018.09.030
19. L. Quintino, “Overview of coating technologies,” in: Surface Modification by Solid State Processing, Elsevier, Cambridge (2014), pp. 1-24. https://doi.org/10.1533/9780857094698.1
20. W. Zhai, L. Bai, R. Zhou, X. Fan, G. Kang, Y. Liu, and K. Zhou, “Recent progress on wear-resistant materials: designs, properties, and applications,” Advanced. Sci., 8, Is. 11, art. no. 2003739 (2021). https://doi.org/10.1002/advs.202003739
21. W. Kuang, Q. Miao, W. Ding, and H. Li, “A short review on the influence of mechanical machining on tribological and wear behavior of components,” The Int. J. of Adv. Manufacturing Technol., 120, 1401-1413 (2022). https://doi.org/10.1007/s00170-022-08895-w
22. H. M. Nykyforchyn, E. Lunarska, V. I. Kyryliv, and O. V. Maksymiv, “Hydrogen permeability of the surface nanocrystalline structures of carbon steel,” Mater. Sci., 50, No. 5, 67-73 (2015). https://doi.org/10.1007/s11003-015-9774-3
23. N. M. Stechyshyn, M S. Stechyshyn, and N. S. Mashovets, Corrosion-Mechanical Wear Resistance of Food Producing Equipment Elements[in Ukrainian], Khmelnytskyi National Univ. Publ. House, Khmelnytskyi (2022).
24. M. Stechyshyn, M. Skyba, N. Stechyshyna, and A. Martynyuk, “Stress-corrosion wear of nitrided steels in acid media,” Mater. Sci., 58, No. 2, 274-280 (2022). https://doi.org/10.1007/s11003-022-00660-4
25. M. S. Stechyshyn, M. V. Luk’yanyuk, V. P. Tereshchenko, and A. I. Beregoviy, “Mechanisms of carbon steels fracture under micro-impact loading in corrosive-abrasive environments,” Visnyk Khmelnytskogo Nationalnogo Univ.[in Ukrainian], Is. 5, 66-74 (2007).
26. M. S. Stechyshyn, N. M. Stechyshyna, A. V. Martynyuk, and M. M. Luk’yanyuk, “Strength and plasticity of the surface layers of metals nitrided in glow discharge,” Mater. Sci., 54, No. 5, 55-60 (2018). https://doi.org/10.1007/s11003-018-0156-5
27. M. S. Stechyshyn, N. M. Stechyshyna, and V. S. Kurskoi, “Corrosion and electrochemical characteristics of the metal surfaces (nitrided in glow discharge) in model acid media,” Mater. Sci., 53, No. 5, 724-731 (2018). https://doi.org/10.1007/s11003-018-0129-8