Load-bearing capacity and deformability of ribbed PLA plastic plate, manufactured using 3D technology

Keywords

plate, plastic, 3D printing, testing, strength, deflections.

Cite as

Demchyna B. H., Vozniuk L. I., Surmai M. I., and Osadchuk T. Yu. Load-bearing capacity and deformability of ribbed PLA plastic plate, manufactured using 3D technology. Physicochemical Mechanics of Materials. 2024. 60(5), 074-078.

https://doi.org/10.15407/pcmm2024.05.074

Abstract

The results of finite-element modeling and experimental research under the load of a stamp of a ribbed floor slab made of PLA plastic, manufactured using 3D printing technology, are presented. The maximum values of the plate deflections and stresses, as well as the value of the limit load, were determined. The experimental and theoretical research results of the ribbed plate were compared.

References

1. M. B. A. Bakar, A. Hermawan, and S. H. Mohd, “Plastic in home building and construction applications,” in: M. S. J. Hashmi (editor), Encyclopedia of Materials: Plastics and Polymers, Vol. 4, Elsevier (2022), pp. 58-67. https://doi.org/10.1016/B978-0-12-820352-1.00195-4
2. I. Perkins, and M. Skitmore, “Three-dimensional printing in the construction industry: A review,” Int. J. of Construction Management, 15, Is. 1, 1-9 (2015). https://doi.org/10.1080/15623599.2015.1012136
3. T. de Rubeis, A. Ciccozzi, D. Paoletti, and D. Ambrosini, “3D printing for energy optimization of building envelope – Experimental results,” Heliyon, 10, Is. 10, e31107 (2024). https://doi.org/10.1016/j.heliyon.2024.e31107
4. M. R. Hasan, I. J. Davies, A. Pramanik, M. John, and W. K. Biswas, “Potential of recycled PLA in 3D printing: A review,” Sustainable Manufacturing and Service Economics, 3, 100020 (2024). https://doi.org/10.1016/j.smse.2024.100020
5. J. W. Stansbury, and M. J. Idacavage “3D printing with polymers challenges among expan-ding options and opportunities,” Dental Materials, 32, Is. 1, 54-64 (2016). https://doi.org/10.1016/j.dental.2015.09.018
6. M. Lay, N. L. N. Thajudin, Z. A. A. Hamid, A. Rusli, M. K. Abdullah, and R. K. Shuib, “3D comparison of physical and mechanical properties of PLA, ABS and nylon 6 fabricated using fused deposition modeling and injection molding,” Composites Part B: Eng., 176, 107341 (2019). https://doi.org/10.1016/j.compositesb.2019.107341
7. H. Kim, E. Park, S. Kim, B. Park, N. Kim, and S. Lee, “Experimental study on mechanical properties of single- and dual-material 3D printed products,” Procedia Manufacturing, 10, 887-897 (2017). https://doi.org/10.1016/j.promfg.2017.07.076
8. L. Blok, M. Longana, H. Yu, and B. Woods, “An investigation into 3D printing of fibre reinforced thermoplastic composites,” Additive Manufacturing, 22, 176-186 (2018). https://doi.org/10.1016/j.addma.2018.04.039
9. S. K. Dhinesh, P. S. Arun, K. K. L. Senthil, and A. Megalingam, “Study on flexural and tensile behavior of PLA, ABS and PLA-ABS materials, Mater. Today: Proc, 45, Is. 2, 1175-1180 (2021). https://doi.org/10.1016/j.matpr.2020.03.546
10. M. Algarni, and Ghazali S. “Comparative study of the sensitivity of PLA, ABS, PEEK, and PETG’s mechanical properties to FDM printing process parameters” Crystals, 11, Is. 8, 995 (2021). https://doi.org/10.3390/cryst11080995
11. T. Galeta, P. Raos, J. Stojšić, and I. Pakši, “Influence of structure on mechanical properties of 3D printed objects,” Procedia Eng, 149, 100-104 (2016). https://doi.org/10.1016/j.proeng.2016.06.644
12. B. Rankouhi, S. Javadpour, F. Delfanian, and T. Letcher, “Failure analysis and mechanical characterization of 3D printed ABS with respect to layer thickness and orientation,” J. of Failure Analysis and Prevention, 16, 467-481 (2016). https://doi.org/10.1007/s11668-016-0113-2
13. B. Demchyna, L. Vozniuk, M. Surmai, S. Havryliak, and Y. Famulyak, “Experimental study of the dome model made using a 3D printer from PLA plastic,” in: AIP Conf. Proc. Int. Scientific Session on Applied Mechanics XI (Bydgoszcz, Poland, 18 November 2022), AIP Publishing, 2949, Is. 1 (2023). Article number 020025. https://doi.org/10.1063/5.0165270
14. Demchyna B., Vozniuk L., and M. Surmai, “Testing of the ribbed dome which is manufactured by 3D printing,” in: Proc. of CEE 2023: Civil and Environmental Engineering and Architecture (Rzeszów, Poland, 6-8 September 2023). Lecture Notes in Civil Engineering, Springer Cham: 438, 70-77 (2024). https://doi.org/10.1007/978-3-031-44955-0_8